Leading 10 usual forklift accidents ， forklift procedure need to take notice of these issues ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the employees unlawfully, the forklift vehicle driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift driver did not put on a seat belt and dropped from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is steady and dependable.
4. The beginning should be slow-moving and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backward. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving position prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal ought to be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or loading. .
8. The height of the load must not block the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the lots does not slide in reverse. The pole can be tilted onward slightly when the lots is lowered to enable very easy positioning of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure Stand-on Electric Pallet Stacker individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is Stand-on Electric Pallet Stacker not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope must be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and go to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844